ES-2310Q
Nachádzate sa v Všetky kategórie
|
 |
Kategórie produktu
RubyTech » Fast Switch » L2 Managed
Parametre
| Hudobný výkon | 150 W (2 x 75 W max.) |
| Frekvenčný prenos | 45 - 20.000 Hz |
| Citlivosť | 86 dB |
Popis
ES-2310Q
10-Port L2 Managed Fast Ethernet Switch with 2 100Base-FX Ports
ES-2310Q is a Managed Fast Ethernet switch that supports SNMP, Web UI and CLI management interface and with 8 ports 10/100Base-TX (RJ-45 connectors) and 2 ports 100Base-FX (SEP). It is a standard switch that meets all IEEE 802.3/u/x Fast Ethernet specifications. In addition, the switch implements the QoS (Quality of Service), VLAN, Mac Filtering Policy, Port Mirror, VLAN and full L2 protocols. It has a rich feature set suitable for streaming VoIP, video, and data traffics for multimedia applications.
In this switch, Port 9, 10 support 2-port 100Base-FX (SEP) , the 2-port fiber is used 2 slots for removable SEP module supporting, they are 100Base-FX fiber module.
Key Features
QoS with Four Priority Queues
The QoS(Quality Of Service) feature provides four internal queues to support four different classifications of traffic. High priority packet streams experience less delay inside the switch, which supports lower latency for certain delay-sensitive traffic. The ES-2310Q can classify the packet as one of the four priorities according to vip port, 802.1p priority tag, DiffServ and/or IP TOS. The QoS operate at full wire speed. The actual scheduling at each egress port can be based upon a strict priority, weighted round robin or a mix of both.
Port Mirroring
This mechanism helps track network errors or abnormal packet transmission without interrupting the flow of data. Allow ingress traffic to be monitored by a single port that is defined as mirror capture port. The mirror capture port can be any 10/100 port, 10/100/1000 port. Mirroring multiple ports is possible but can create congestion at the mirror capture port.
Q-in-Q VLAN for performance & security
The VLAN feature in the switch offers the benefits of both security and performance. VLAN is used to isolate traffic between different users and thus provides better security. Limiting the broadcast traffic to within the same VLAN broadcast domain also enhances performance. Q-in-Q, the use of double VLAN tags is an efficient method for enabling Subscriber Aggregation. This is very useful in the MAN.
Isolated Group, Provide Secure for Certain Ports
The isolated group feature allows certain ports to be designated as protected. All other ports are non-isolated. Traffic between isolated group members is blocked. Traffic can only be sent from isolated group to non-isolated group.
Mac-based 802.ad LACP with automatic link fail-over
Dynamic fail-over means packets will not get assigned to any trunk member port that has failed. If one of the ports were to fail, traffic will automatically get distributed to the remaining active ports.
802.1x Access Control Improve Network Security
802.1x features enable user authentication for each network access attempt. Port security features allow you to limit the number of MAC addresses per port in order to control the number of stations for each port. Static MAC addresses can be defined for each port to ensure only registered machines are allowed to access. By enabling both of these features, you can establish an access mechanism based on user and machine identities, as well as control the number of access stations.
802.1d Compatible & 802.1w Rapid Spanning Tree
For mission critical environments with multiple switches supporting STP, you can configure the switches with a redundant backup bridge path, so transmission and reception of packets can be guaranteed in event of any fail-over switch on the network.
Broadcast/Multicast/unknown-unicast Storm Control
To limit too many broadcast/multicast/unknown-unicast flooding in the network, broadcast/multicast storm control is used to restrict excess traffic. Threshold values are available to control the rate limit for each port. Packets are discarded if the count exceeds the configured upper threshold.
Standard compliance
l IEEE 802.3 10Base-T
l IEEE 802.3u 100Base-TX
l IEEE 802.3x flow control capability
l ANSI/IEEE 802.3 auto-negotiation
l IEEE 802.1q VLAN
Subscriber Interface
l 1-8 10/100Mbps Fast Ethernet ports.
l 9,10 are Fast Ethernet Fiber ports with SEP module
l Auto-Negotiation and Auto-MDIX
l Backpressure flow control for half duplex.
l IEEE 802.3x flow control for full duplex
l Connector: 8 ports RJ-45 and 2 ports Fiber (SEP)
Performance
Switching capacity:
l Non-blocking switch fabric supports up to 8 FE+2 SEP ports
l 8 K MAC addresses
l 256k packet buffer and 128k control memory
VSM (Virtual Stacking Management)
l Supports 16 devices stacking
l Multiple switches can be managed via one IP address, just like software stacking
l Low cost and easily to establish network environment, not extra hardware require.
l No center on the physical location of wiring closets
VLAN
l Supports SVL/IVL configuration to meet your VLAN requirement
l Port-base VLAN
l IEEE802.1q tag-base VLAN, 4094 max, up to 256 active VLANs including static plus dynamic entry
l IEEE802.1q tag-base VLAN
l Flooding unknown VLAN frame setting, can flood packet with some VLAN tag associated to a invalid/inactive VLAN
l In tag-base VLAN, supports egress/ingress packet filter
l Q-in-Q is an efficient method for enabling Subscriber Aggregation.
Qos
l Port Based (VIP Port), 802.1p , TOS and Diffserv(IPv4/IPv6) based QoS packet classification
l Supports four level priority queues to prioritize in-bound and out-bound traffic
l Supports two scheduling, WRR and Strict
l Supports priority in a Q-in-Q tag
Bandwidth Control
l Supports bandwidth rating per port ingress and egress rate limit 1000Mbps with 1Mbps increment
Broadcast Storm
l Multicast/Broadcast/Unknown-Unicast Storm suppression
Transmission Mode
l 10/100Mbps support full or half duplex
Transmission Speed
l 10/100Mbps for TP and 100Mbps for Fiber
Port Mirroring
l Support 1: N RX port mirroring
l Supports port sniffer function with 3 modes:(TX Monitor Mode, RX Monitor Mode and TX-RX pair Monitor Mode)
Isolated Group
l Provide one group allows certain ports to be designated as protected
Restricted Group
l Can decide the direction of transmitting packets for the specific port
Protocol
LACP
l 2 Fast Ethernet +1 Gigabit Ethernet groups
l Per-group max 4 member
l Provides DA, SA and DA+SA Mac-based trunking with automatic link fail-over
GVRP/GARP
l 802.1q with GVRP/ GARP
Multicasting
l Supports IGMP snooping including active and passive mode
STP/RSTP
l 802.1d/1w
Network Security
l 802.1x access control
l Isolated group
l Restricted group
l Management Access Policy Control
l Static mac, to limit which mac addresses can pass through or not
l Mac addresses learning limit, to set up the maximum amount of mac that each port can learn
SNMPv1, v2c Network Management
MIB Files: Interface MIB, Address Translation MIB, Statistics Group 1, History Group 2, Alarm Group 3, Event Group 9, IP MIB, ICMP MIB, TCP MIB, UDP MIB, SNMP MIB, RFC 1213 MIB (MIB-II), RFC 1757 RMON MIB, RFC 1493 Bridge MIB, RFC 1643 Ethernet MIB, Enterprise MIB
Technical Specification
LED Description
LED
Color
Function
Global
POWER
Green
Lit when +5V power is coming up
Global
CPU
Green
Blinks when CPU is active
Port 1-8
LINK/ACT
Green
Lit when connection with remote device is good
Blinks when any traffic is present
Port 1-8
10/100Mbps
Green/Amber
Lit Green when TP link on 100Mbps speed
Off when 10Mbps or no link occur
Port 9,10
SEP
Green
Lit when SEP connection with remote device is good
Blinks when any traffic is present
Network Interface
Category
Connector
Transmission
Max. Cable Length
Wavelength
10-T/100-TX
RJ-45
Full/Half Duplex
100M
/
100-FX (M-M)
SC/ST
Full/Half Duplex
2Km 50/125μ
1310nm
100-FX (S-M)
SC
Full/Half Duplex
5/20/60Km 9/125μ
1310nm
100-FX (S-M)
Bidi-SC
Full/Half Duplex
20Km 9/125μ
1310nm
1550nm
Full Forwarding Packet Rate: PPS (64 Bytes packets per second)
Forwarding Rate
Speed
14,880PPS
10Mbps
148,800PPS
100Mbps
Cable and Maximum Length
Feature
Detailed Description
TP
Cat. 5 UTP cable, up to 100m
100Base-FX SC/ST M-M
Up to 2Km
100Base-FX SC S-M
Single-Mode Fiber, up to 5/20/60Km
100Base-FX WDM SC S-M
Single Fiber, BiDi 20Km
Hardware Spec
Feature
Detailed Description
Voltage
100~240 VAC
Frequency
50~60 Hz
Consumption
8.9W
Ambient Temperature
0° to 40°C
Humidity
5% to 90%
Dimensions
44(H) x 220(W) x 130.5(D) mm
Safety
Comply with FCC Part 15 Class A & CE Mark Approval
Ordering Information
■Model
ES-2310Q
10-Port L2 Managed Fast Ethernet Switch with 2 100Base-FX Ports
Optional SEP Fiber Module
Model
Description
FM-SEP.SC SEP, FE SC Multi-Mode Fiber Module 1310nm
FM-SEP.SC.S05 SEP, FE SC Single-Mode 5km Fiber Module 1310nm
FM-SEP.SC.S20 SEP, FE SC Single-Mode 20km Fiber Module 1310nm
FM-SEP.SC.S40 SEP, FE SC Single-Mode 40km Fiber Module 1310nm
FM-SEP.SC.S60 SEP, FE SC Single-Mode 60km Fiber Module 1310nm
FM-SEP.BS5.S20
SEP, FE BiDi SC 20km Module Single Fiber 1550nm, Type 1
FM-SEP.BS3.S20 SEP, FE BiDi SC 20km Module Single Fiber 1310nm, Type 2
Galéria
Dotazy k produktu
K produktu ešte nebol pridaný žiadny dotaz
Pre pridanie komentáru musíte byť prihlásený
Naposledy navštívené produkty
 EM-C106 |  EM-C107C |  ES-2126C/D |  ES-2310Q |